SunBright® High Intensity Reflective Labels, Digits and Signs, SB
  1. Scope. This specification covers labels and signs made from high intensity, retroreflective sheeting having encapsulated micro-prisms. The reflective film is not metallized and is reflective at night, even when wet. Typically, labels, markers and signs made from the reflective film are applied by hand either to the Electromark plastic panel or to a metal surface. The labels shall a heavy adhesive having a high initial tack that is appropriate for rough or textured transformer surfaces.
  2. Government Specifications. The reflective label material shall meet the following criteria:
  • US DOT. Standard specifications for construction of Roads and Bridges on Federal Highway Projects FP-85, November 1989, Section 718-Reflective SheetingType III-C
  • ASTM D-4956-90. December, 1990, Standard Specification for Retroreflective Sheeting for Traffic ControlType 4, Class 1
  1. CIE Color Values. The film shall have the following CIE daytime chromaticity corner coordinates:
     
    2. Points White   Yellow  
      X Y X Y
    1 0.303 0.287 0.498 0.412
    2 0.368 0.353 0.557 0.442
    3 0.340 0.380 0.479 0.520
    4 0.274 0.316 0.438 0.472

 

  1. Daytime Luminance. The film shall have the following Luminance Factors (Cap Y%):
     
    2. White Yellow
    50 minimum 30 minimum
    -- 45 maximum

 

  1. Reflective Intensity. The film shall have the following coefficient of retroreflection (as measured in candelas per footcandle per sq ft):
     
    2. Observation Angle Entrance Angle White Yellow
    0.1º -4º 400 270
    0.1º +30º 120 75
    0.2º -4º 250 170
    0.2º +30º 80 54
    0.5º -4º 135 100
    0.5º -+30º 55 37

 

  1. Thickness. The film shall be fabricated from a 0.0025" thick acrylic adhesive, a 0.0115" thick methylacrylate film and a 0.0055" thick blue polyethylene liner.
  2. Adhesive. The adhesive shall be a solvent based acrylic adhesive having the following values (using PSTC #1 at 70ºF and a 24 hour dwell):
     
    3. Bonding Surface Ounces/Inch of Width
    Lexan (corona treated) 100
    Stainless Steel 120
    Polyester 100

 

  1. Operating Temperature Range. The markers must be capable of operation within the temperature range of -20ºF to +180ºF with no obvious degradation or signs of wear or peeling/flagging.
  2. Ink Color & Printing. The background of the digits shall be screen printed using solvent based, black, gloss ink, NazDar 7700. The type face shall be [Cleaview Extended, Helvetica Extended or Univers Extended].
  3. Tab or Backslit. Markers shall have an at least a 1/8" tab for easy peeling of the liner. Markers may be packaged individually or on a notebook sheet. The tab on the notebook sheet may be at the margin of the page. Notebook sheets shall have holes in the left margin so that they can be included in a standard three-ring binder.
  4. Installation. Markers shall be applied to a clean, dry surface. If the markers are not applied to an Electromark panel, use a 3M Scotchbrite pad (or equivalent) to remove any surface oxidation, dirt or paint chalking from application surface and to rough up the surface. After this treatment the surface shall be cleaned with Surface Prep 77 or equal. Markers shall be applied at temperatures above 40ºF. After proper adhesive cure, markers shall be tamper-resistant.
  5. Packaging. 25 pieces shall be packaged in a polyethylene bag or vacuum formed package. Bags or packages shall be packaged in a corrugated carton. Each carton shall contain the same legend. The outside of each box shall be labeled with the part number, utility code number, description and quantity.
  6. Warranty. The products are to be guaranteed by the vendor to be free of workmanship or material defect. If, for reasons of workmanship or material defect, the marker becomes unreadable during a period of ten years, the vendor shall replace the marker at no additional charge.

    7.  

     

    ELECTROMARK'S OBLIGATION UNDER THIS WARRANTY IS LIMITED TO REPLACEMENT OF THE PRODUCT. OUR PRODUCT IS SOLD WITHOUT ANY WARRANTY OF MERCHANTABILITY AND WITHOUT ANY WARRANTY THAT OUR PRODUCT IS GOOD FOR ANY PARTICULAR PURPOSE. OUR PRODUCTS ARE SOLD WITH THE UNDERSTANDING THAT THE USER WILL DETERMINE THEIR ADAPTABILITY FOR HIS INTENDED USES. WE ARE NOT BOUND BY ANY OTHER WARRANTY, EXPRESSED OR IMPLIED. UNDER NO CIRCUMSTANCES ARE WE LIABLE FOR ANY LOSS, DAMAGE, EXPENSE OR CONSEQUENTIAL DAMAGES OF ANY KIND ARISING OUT OF THE USE OR INABILITY TO USE OUR PRODUCTS.